EIFS FOR COMMERCIAL AND HIGH RISE | EIFS FOR RESIDENTIALAND LOW RISE | EIFS FOR INSULATED CONCRETE FORM (ICF) |
PUCCS EIFS for Commercial and High Rise construction has been evaluated by CCMC for compliance to the Technical Guide for EIFS, and is certified for use on buildings required to be of non-combustible construction and on buildings over three storeys in height. This system incorporates a trowel-applied air/moisture barrier, and dependent upon the configuration of the wall assembly, may also provide the necessary condensation control. | PUCCS EIFS for Residential and Low Rise Construction is an insulated cladding system specifically intended for use on wood sheathed walls. This system includes first and second planes of protection from precipitation, and a geometrically-defined drainage cavity that is 10 mm deep and 37% open. This system has been evaluated by the Canadian Construction Materials Centre (CCMC), this system complies with the CAN/ULC-S716.1 EIFS Materials and Systems Standard, and this system is certified to the test requirements of Article 3.2.3.8 of the National Building Code of Canada. | PUCCS EIFS for Insulated Concrete Form (ICF) construction combines the continuous insulation of EIFS and ICF to deliver the ultimate thermal performance! While this system is certified for use on buildings required to be of non-combustible construction and on buildings over three storeys in height, CCMC has yet to evaluate ICF as a substrate for EIFS |
Specs Autocad | Specs Autocad | Specs Autocad |
INSULROCK/COMMERCIAL & HIGH RISE CONSTRUCTION | INSULROCK NC/WALLS REQUIRING NON- COMBUSTIBLE CLADDING |
The DuROCK series of InsulROCK EIFS provides moisture control through the use of a secondary barrier to moisture intrusion, which may also be used to control air leakage. This barrier, combined with the system's ability to drain incidental moisture, makes InsulROCK EIFS well suited for cladding buildings of any size.The DuROCK InsulROCK System is intended for use on non-wood substrates. This system may incorporate either DuROCK Cement Bear (air/moisture barrier) or, where the design permits, DuROCK Vapour Block | The DuROCK InsulROCK Non-Combustible System is intended for use on walls where the building code does not permit the use of foamed plastic (ie. polystyrene) insulation. This typically applies to walls in close proximity to a property line or another building |
Specs Autocad | Specs Autocad |
Stucco Plus incorporates a polymer-enhanced, fibre-reinforced base coat for superior adhesive and cohesive strength, as well as a polymer-based finish which is available in a variety of textures and infinite colours. Metal lath is not required when applying Stucco Plus to cast-in place concrete or concrete masonry units. Please refer to our system specifications for further details. Stucco Plus can be adapted to rainscreen construction with the placement of a drainage mat or wood strapping between the sheathing membrane and the metal lath. Please refer to our system specifications for further details. |
BLOCK OR BRICK WALL CONSTRUCTION | FRAME CONSTRUCTION | RAINSCREEN | MASS WALL CONSTRUCTION | |
DUROCK DEFS DIRECT APPLIED EXTERIOR FINISH SYSTEM |
DuROCK DEFS is intended for use on ventilated, steel frame, soffit and canopy assemblies that enclose unheated space. DuROCK DEFS may be used on similar wood frame assemblies providing there is wood sheathing separating the DEFS substrate from the framing. DuROCK DEFS may also be used over concrete. |
Specs Autocad |
A comprehensive guide to maintaining DuROCK Systems
VAPOUR BLOCK | ROLLER BEAR | POLAR BEAR | CEMENT BEAR |
DuROCK Vapour Block is formulated with a co-polymer styrene-butadiene emulsion. It is a trowel applied high performance coating, applied onto non-combustible substrates as an air, vapour, and moisture barrier for DuROCK PUCCS and InsulROCK Systems. The low water absorption combined with a high flexural strength makes Vapour Block an ideal water penetration barrier for use on exterior wall systems; in particular glass-fibre faced gypsum sheathing, cement board, concrete, or masonry substrates. Check with DuROCK for use on other substrates. As part of an air barrier system for a wall assembly, Vapour Block is compatible with most transition membranes comprised of bituminous SBS with fabric or cross-laminated polyethylene backing, as well as bituminous mastics and polyurethane foam sealants. Refer to DuROCK system specifications for product specific guidelines. | Roller Bear is intended for use as the first coat in a two-coat moisture barrier system that serves as the second plane of protection behind DuROCK PUCCS EIFS. Roller Bear is a factory-blended, ready-to-use, non- cementitious, polymeric coating that is supplied in 19 L (5 US gallon), 28 kg (62 lb) pails and is applied by spray, brush, or roller in a continuous layer to achieve a minimum dry thickness of 0.28 mm (11 mils) per coat. | DuROCK Polar Bear is formulated with a 100% acrylic emulsion. It is a trowel-applied high performance coating for use over wood substrates as both an air and moisture barrier, in particular for the DuROCK PUCCS RMC-1 and InsulROCK RMC-1 Systems. Polar Bear contains fibers that enhance the cohesive and tensile strength for added durability. Polar Bear can also be used as an insulation adhesive. The low water absorption combined with a high flexural strength makes Polar Bear an ideal water penetration barrier for use on exterior wall systems; in particular plywood 12.7 mm (½ inch) thick and oriented strand board (OSB), minimum 11.1 mm (7/16 inch) thick. Check with DuROCK for use on other substrates. As part of an air barrier system for a wall assembly, Polar Bear is compatible with most transition membranes comprised of bituminous SBS with fabric or cross-laminated polyethylene backing, as well as bituminous mastics and polyurethane foam sealants. Refer to DuROCK system specifications for product specific guidelines. | DuROCK Cement Bear is formulated with a 100% acrylic emulsion that is field-mixed with Portland Cement. It is a trowel-applied high performance coating for use on non-combustible substrates, as an air and moisture barrier for DuROCK PUCCS and InsulROCK Systems. Cement Bear contains fibres that enhance the cohesive and tensile strength for added durability. Cement Bear can also be used as an insulation adhesive. The low water absorption combined with a high flexural strength makes Cement Bear an ideal water penetration barrier for use on exterior wall systems; in particular glass-fibre faced gypsum sheathing, cement board, concrete or masonry substrates. Check with DuROCK for use on other substrates. As part of an air barrier system for a wall assembly, Cement Bear is compatible with most transition membranes comprised of bituminous SBS with fabric or cross-laminated polyethylene backing, as well as bituminous mastics and polyurethane foam sealants. Refer to DuROCK system specifications for product specific guidelines. |
Data Sheet MSDS | Data Sheet MSDS | Data Sheet MSDS | Data Sheet MSDS |
ONE STEP READY MIX | BIG EXTRA (BRUSH IT GREY) | ONE STEP CONCENTRATE |
DuROCK One Step Ready Mix is a formulated dry-mix cement parging, leveling coat and stucco base coat that is field-mixed with water. It is a trowel-applied polymer modified cement plaster, a mixture of Portland cement, silica sand, and dry-resins. It is a versatile product that can be used as a leveling coat for conventional stucco, concrete and masonry substrates, and also as the scratch and brown coats for DuROCK Stucco Plus.One Step Ready Mix has the benefit of high-early compressive and tensile strength, with excellent freeze-thaw stability and low water absorption. It is a convenient product since it requires only water to be added on site.One Step Ready Mix contains 1/4" fibers that enhance the cohesive and adhesive strength for added durability. It is also a low-shrinkage polymer modified cement that makes it ideal for uneven leveling coats. | B.I.G Extra is a dry mix cement parge specifically designed to enhance the appearance of cast-in-place concrete walls. B.I.G Extra is polymer modified and requires only the addition of water. B.I.G Extra hides surface irregularities such as cold joints, colour variations, and form distortions. B.I.G Extra can also be used to disguise minor cracking and honeycombs. B.I.G Extra is available in 44 lb (20 kg) bags. | DuROCK One Step Concentrate is a formulated dry-mix concentrate for use in cement parging, leveling coats and stucco base coats. It is field-mixed with Portland cement, silica sand and water. One Step Concentrate is a trowel or spray-applied polymer modified cement plaster, a mixture of minerals, fine aggregates, and dry-resins. It is a versatile product that can be used as a leveling coat for conventional stucco, concrete and masonry substrates, and also as the scratch and brown coats for DuROCK Stucco Plus.One Step Concentrate has the benefit of high-early compressive and tensile strength, with excellent freeze-thaw stability and low water absorption. One Step Concentrate contains 1/4" fibers that enhance the cohesive and adhesive strength for added durability. It is also a low-shrinkage polymer modified cement that makes it ideal for uneven leveling coats. |
Data Sheet MSDS | Data Sheet MSDS | Data Sheet MSDS |
PREP COAT | PREP COAT PLUS | PREP COAT D | PREP COAT Q | PERFECT PARGE |
DuROCK Prep Coat is 100% acrylic emulsion that is field-mixed with Portland Cement. It is a trowel-applied high performance coating for use on DuROCK PUCCS and InsulROCK Systems as a non-combustible base coat and adhesive. Prep Coat is a flexible and durable base coat that can also be used as a leveling coat for stucco, concrete and masonry substrates. It has excellent freeze-thaw stability, low water absorption, breathable to water vapour and non-combustible. It is a convenient product since it requires only water to be added on site. | DuROCK Prep Coat Plus is 100% styrene acrylic emulsion that is field-mixed with Portland Cement. It is a trowel-applied high performance coating for use on DuROCK PUCCS RMC and InsulROCK RMC Systems as a base coat and adhesive with enhanced flexibility and strength. Prep Coat Plus is a flexible and durable base coat that can also be used as a leveling coat for stucco, concrete and masonry substrates. It has excellent freeze-thaw stability, low water absorption, and breathable to water vapour. Prep Coat Plus can be applied as a high-build leveling coat, for added impact resistance on EIFS or to make a wall plumb and flat, applied up to 6.4 mm (1/4 inch) thick in a single pass if required. | DuROCK Prep Coat is dry polymer based dry-mix material that is field-mixed with water. It is a trowel-applied high performance coating for use on DuROCK PUCCS and InsulROCK Systems as a non-combustible base coat and adhesive. Prep Coat D is a flexible and durable base coat that can also be used as a leveling coat for stucco, concrete and masonry substrates. It has excellent freeze-thaw stability, low water absorption, breathable to water vapour and non-combustible. It is a convenient product since it requires only water to be added on site. | DuROCK Prep Coat Q is a fast drying, dry polymer based dry-mix material that is field-mixed with water. It is ideal for use in cold temperature, high humidity conditions. It is a trowel-applied high performance coating for use on DuROCK PUCCS and InsulROCK Systems as a non-combustible base coat and adhesive. Prep Coat Q is a flexible and durable base coat that can also be used as a leveling coat for stucco, concrete and masonry substrates. It has excellent freeze-thaw stability, low water absorption, breathable to water vapour and non-combustible. It is a convenient product since it requires only water to be added on site. | DuROCK Perfect Parge is a polymer based dry-mix material that. It is a trowel-applied adhesive for use in the attachment of decorative moldings and EPS trim on DuROCK PUCCS and InsulROCK Systems. Perfect Parge is a flexible and durable base coat that can also be used as a leveling coat for stucco, concrete and masonry substrates. It has excellent freeze-thaw stability, low water absorption, breathable to water vapour and non-combustible. It is a convenient product since it requires only water to be added on site. |
Data Sheet MSDS | Data Sheet MSDS | Data Sheet MSDS | Data Sheet MSDS | Data Sheet MSDS |
FIBREGLASS MESH | EPS BOARD | UNI-TRACK | UNI-FLASH | SEAL & COAT EIFS TAPE |
Mesh for DuROCK Exterior Insulation Finish Systems is made of alkali-resistant fibreglass. All mesh is made by a DuROCK-approved manufacturer, with DuROCK's logo plainly visible on the 4.5 and 6.0 ounce reinforcing mesh products. | Expanded Polystyrene (EPS) insulation board for DuROCK Exterior Insulation Finish Systems is made of 100% virgin polystyrene resin, aged and cut in accordance with the requirements of ASTM E2430, and compliant with ULC-S701. EPS insulation board is made by a DuROCK-approved manufacturer, and is packaged in bags with DuROCK's logo plainly visible. Please refer to EIF System specifications for applicable thicknesses & sheet size. | DuROCK's patented Uni-Track is a PolyVinyl Chloride (PVC) extrusion designed to be used at horizontal terminations and at horizontal joints where DuROCK Exterior Insulation Finish Systems are expected to drain. Its one-size-fits-all profile eliminates the need to stock different profiles for every insulation thickness. DuROCK Uni-Track is three inches (76 mm) high, one inch (25 mm) wide, and eight feet (2.44 m) long. It is white in colour, but can be painted with most exterior latex paints. | DuROCK's patented Drainage Flash is a PolyVinyl Chloride (PVC) extrusion designed to be used at window head locations where DuROCK Exterior Insulation Finish Systems are expected to drain. It's one- size-fits-all profile eliminates the need to stock different profiles for every insulation thickness. DuROCK Drainage Flash is eight feet (2.44 m) long and is available in 1¾ inch (46 mm) and 2 inch ( 52 mm) widths. It is white in colour, but can be painted with most exterior latex paints. | Seal & Coat EiFS Tape is a self-adhering membrane composed of a polyester fabric laminated to rubberized asphalt adhesive. The fabric strengthens the material while providing a surface which bonds with most coatings. The adhesive provides a waterproof, self-sealing layer which aggressively sticks to most clean, dry surfaces. |
Data Sheet MSDS | Data Sheet MSDS | Data Sheet MSDS | Data Sheet | Data Sheet MSDS Application |
TROWEL FINISHES | SPRAY FINISHES | PLUS FINISHES | ROLLER FINISHES |
DuROCK Trowel Finishes are premixed, water-based, 100% acrylic coatings available in several textures and unlimited colours. DuROCK Trowel Finishes are flexible, breathable, water-repelling, dirt pick-up resistant (DPR), ultra-violet resistant finishes consisting of granulated quartz or marble, pigment, resin and other additives specially formulated for both exterior and interior use. DuROCK Trowel Finishes are ideally suited for both new and/or retrofit construction. DuROCK Trowel Finishes are available in several textures distinguished by their aggregate size and application technique. Coarse Coat, Desert Sand, Grain, Marble Coat, Max Coat, Pebble Rock, Sand Coat, Spacco, and Venetian finishes are trowel-applied coatings designed for use over wall and ceiling areas. Fine Coat and Pebble Coat finishes are trowel-applied coatings designed for use over details such as cornice, quoins, columns, etc. | DuROCK Spray Finishes are premixed, water-based, 100% acrylic coatings available in several textures and unlimited colours. DuROCK Spray Finishes are flexible, breathable, water-repelling, dirt pick-up resistant (DPR), ultraviolet resistant finishes consisting of silica sand, pigment, resin and other additives formulated for both exterior and interior use. DuROCK Spray Finishes are ideally suited for both new and/or retrofit construction. Whereas Pebble Spray and Fine Spray are intended for details only, the remaining DuROCK Spray Finishes are designed for use over wall and ceiling areas. | DuROCK Plus Finishes are formulated with 100% acrylic emulsions designed especially for use in elastomeric wall coatings, providing outstanding exterior durability, as well as excellent elasticity and elongation properties that are required to bridge continually over cracks without wrinkling. Due to the low glass-transition temperature, these finishes are able to maintain flexibility across a broad range of temperatures.DuROCK Plus Finishes can be color-tinted, and are intended for application on vertical wall surfaces. These finishes are most effective when applied over rigid substrates (such as cement plasters and concrete), and can also be used with DuROCK EIFS and Exterior Finishing Systems. DuROCK Plus Finishes are formulated to have excellent dirt-pick-up resistance, and superior water resistance as well as resistance to chalking. The dirt pick-up resistant chemistry of DuROCK Plus Finishes enables the coating to maintain its attractive appearance, while providing superior resistance to the effects of acid rain, pollution and ultra-violet light. Water beads on the surface thereby washing away the dirt. DuROCK Plus Finishes are permeable to water vapour, which permits open vapour diffusion through wall assemblies. | DuROCK Roller Finishes are premixed, water-based, 100% acrylic coatings available in several textures and unlimited colours. DuROCK Roller Finishes are flexible, breathable, water-repelling, dirt pick-up resistant (DPR), ultraviolet resistant finishes consisting of fine fillers, pigment, resin and other additives formulated for both exterior and interior use. DuROCK Roller Finishes are ideally suited for both new and/or retrofit construction. Roll On (small aggregate), Roll On Coarse (large aggregate) and Airless (no aggregate) are intended for use on decorative mouldings and a variety of wall surfaces. |
Data Sheet MSDS | Data Sheet MSDS | Data Sheet MSDS | Data Sheet MSDS |
ANGELSTONE | TRICOL | GEMSTONE | UNIGUM | SPACCO | CRYSTAL COAT | POOL QUARTZ |
DuROCK Angel Stone is ideal for use in interior or exterior applications, in new construction or renovations, and in commercial, industrial, institutional and residential projects. DuROCK Angel Stone is a decorative textured protective coating engineered for use over any DuROCK system. DuROCK Angel Stone is a 100% acrylic finish containing bronze mica flakes and pearlescent pigments giving the finish a shimmering effect. DuROCK Angel Stone is a trowel-applied finish texture available in hundreds of colours. | DuROCK Tricol finish is a premixed, water-based, acrylic, quartz stone finish available in many colour combinations. DuROCK Tricol can be both trowel and spray-applied, used for wall and ceiling areas, as well as for details such as cornice, quoins, columns, etc. | DuROCK Gemstone finish is a premixed, water-based, acrylic, quartz stone finish available in many colour combinations. DuROCK Gemstone can be both trowel and spray-applied, used for wall and ceiling areas, as well as for details such as cornice, quoins, columns, etc. | Unigum is designed for use where an elastic, waterproof, dirt-resistant coating is required. Unigum is a premixed, water-based, elastomeric acrylic coating available in unlimited colours. Unigum actually bridges cracks - spanning the crack as it expands - and returning to its original form when the crack contracts. Unigum's ability to resist ultraviolet degradation and its low-temperature flexibility ensures it will retain its colour and overall appearance for years to come. | DuROCK Spacco is a decorative protective coating designed for use as a textured free hand faux finish. DuROCK Spacco is ideal for use in both interior and exterior applications, in new construction or renovations, and in commercial, industrial, institutional and residential projects. DuROCK Spacco is a 100% acrylic, flexible, breathable coating. DuROCK Spacco is a trowel-applied finish texture and upon request, can be custom coloured to match any customer-specified colour. | DuROCK Crystal Coat is a gypsum-based decorative textured protective coating designed for use as a textured, free hand faux finish base coat. It has been designed to replace conventional gypsum based architectural wall finishes. DuROCK Crystal Coat is ideal for use in interior applications, in new construction or renovations, and in commercial, industrial, institutional and residential projects. DuROCK Crystal Coat is a 100% acrylic, flexible, breathable coating. | Pool Quartz is a complete pool plaster mix that is a combination of white Portland cement, crushed marble, mineral fillers, additives and 3M Colour Quartz. Pool Quartz cures to a smooth, hard surface. Pool Quartz has excellent abrasion resistance and with the addition of 3M Colour Quartz it performs upwards of three times better against both mechanical and chemical wear compared to conventional plaster. |
Data MSDS | Data MSDS | Data MSDS | Data MSDS | Data MSDS | Data | Data |
TOPPING CRETE
Topping Crete DM217 is a multi-component cementitious compound of finely graded silica aggregates plus other additives to provide a highly balanced formula, for a highly rated performance.
Topping Crete Design Mix provides an easy to trowel on plastic mix from thicknesses of l" to a feather edge. Test data carried out at Ortech Corporation resulted in superior qualities as follows: Compressive, flexural, tensile and shear bond. Low moisture absorption and an excellent freeze-thaw stability.
EXTRAFLO
ExtraFlo Self Levelling Floor Finish is a redispersable polymer modified cementitious floor coating that is fast setting and finishes to a smooth, non-textured, flat surface. ExtraFlo is designed for use over existing concrete. ExtraFlo is grey in colour and is available in 50 lb (22.7 kg) bags.
ONE STEP READY MIX
DuROCK One Step Ready Mix is a formulated dry-mix cement parging, leveling coat and stucco base coat that is field-mixed with water. It is a trowel-applied polymer modified cement plaster, a mixture of Portland cement, silica sand, and dry-resins. It is a versatile product that can be used as a leveling coat for conventional stucco, concrete and masonry substrates, and also as the scratch and brown coats for DuROCK Stucco Plus.One Step Ready Mix has the benefit of high-early compressive and tensile strength, with excellent freeze-thaw stability and low water absorption. It is a convenient product since it requires only water to be added on site.One Step Ready Mix contains 1/4" fibers that enhance the cohesive and adhesive strength for added durability. It is also a low-shrinkage polymer modified cement that makes it ideal for uneven leveling coats.
B2000
DuRock B2000 is an acrylic-modified cementitious dry mix base coat designed for use over Expanded Polystyrene (EPS) Insulated Concrete Forms (ICF). B2000 forms a strong yet flexible, crack resistant base coat that is intended for use on the exterior, above-grade portion of ICF foundation walls. B2000 has high flexural and bond strength, is water vapour permeable, and has excellent freeze/thaw stability with low water absorption and low shrinkage.
BIG EXTRA (BRUSH IT GREY)
B.I.G Extra is a dry mix cement parge specifically designed to enhance the appearance of cast-in-place concrete walls. B.I.G Extra is polymer modified and requires only the addition of water. B.I.G Extra hides surface irregularities such as cold joints, colour variations, and form distortions. B.I.G Extra can also be used to disguise minor cracking and honeycombs. B.I.G Extra is available in 33 lb (15 kg) bags.
ONE STEP FINE PARGE
DuROCK Fine Parge is a formulated dry-mix cement parging, leveling coat and stucco base coat that is field-mixed with DuROCK Pure Cement Binder or Prep Coat. It is a trowel-applied polymer modified cement plaster, a mixture of Portland cement and fine aggregates. Fine Parge is a versatile product that can be used as a leveling coat for conventional stucco, concrete and masonry substrates when mixed with Pure Cement Binder, and Fine Parge can also act as a repair base coat for EIFS when mixed with Prep Coat.
TIOCOAT
TIOCOAT is a high-strength elastomeric coating that provides the ultimate in reflectivity and weather resistance. TIOCOAT™'s tough white finish resists abrasion, biological growth, dirt and extreme weather conditions. This versatile roofing system can be applied on a large variety of roofs such as BUR, Mod-bit, EPDM, concrete and asphalt.
The TIOCOAT™ elastomeric roof coating system creates a uniform, seamless surface that remains flexible even at low temperatures, resulting in a longer roof cycle. TIOCOAT™ provides 89% reflectivity of solar radiation, which will significantly reduce the buildings energy requirements and help combat Heat Island Effect
JEWELSTONE
Jewel Stone is the ultimate in acrylic modified cement-based coatings that transforms everyday concrete into beautiful decorative faux stone finishes. Jewel Stone can be used to restore and beautify old deteriorating concrete. It is ideal for walk ways, terraces, patios, pool areas, or any industrial or recreational flooring that requires the look and performance of stone. The luxurious and classic beauty of hand laid stone, slate, flagstone, fieldstone, tile or wood plank in any combination of colours can be achieved with Jewel Stone at a very affordable price.
AGGREGATE/SPACCO
Aggregate is a part of our Smoothrock line. It is an acrylic plaster with a large silica particle for high build distressed effects. Aggregate can be best described as a Mediterranean finish and is ideal when the installation calls for a heavy textured medium on the wall. Aggregate can be tinted integrally, it can be layered in its natural neutral base and washed with a tinted glaze, or it can be applied in several blended colors and treated with an artistic hand. This product is often used to replicate the look of antique walls. Aggregate will not shrink or crack and performs well in high traffic areas. Stencils and decorative paint techniques can be applied over Aggregate finish to further enhance its visual appeal. This product is a water-based acrylic and available in a wide range of colors.
INDIANA LIMESTONE
Indiana Limestone is a dry blend of cementitious compounds & acrylic resins that have been formulated to allow the artisan to create simulated stone effects. Designed for interior wall applications, Indiana Limestone has great design potential and is ideal for carving logos, silk screening, embossing designs as well as applying a patina acid wash over the finish. Polished stone, coral reef or fossil stone are just some of fabulous textures that can be achieved with this product. A tinted glaze can also be applied to Indiana limestone to highlight its' texture and achieve depth.
DURASILK
Durasilk is one of our newest Eco-Friendly products. It is a thick ceramic glaze that can be used as a highlight over almost any texture. Itcontains a tiny mica flake that adds dimension to faux basecoats like Venetian plaster. Durasilk can be trowel, brush, roller or spray applied in any color. Durasilk can also be rolled over existing painted surfaces to increase abrasion resistance while adding a tasteful designer appearance. A marble effect may be achieved through color blending when used over a base texture such as Versiplast or Venetian plaster. When Durasilk is rolled over paint or texture the application time is a fraction of the labor required for most other faux systems.
SPRAY STONE (T.O. STONE TOP COAT SPRAYED BASECOAT PRIMER 100)
Spraystone is a flexible sprayable production faux finish that renders an old world plaster effect in any color. Spraystone was designed for rapid volume install. It is a two part system comprised of a basecoat and topcoat that can be sprayed or rolled. The combination of the silica paint basecoat and the ceramic reinforced topcoat offers a finish that is extremely durable and is subtle enough to be used in whole house applications. If you are seeking a finish that looks and feels like stone, applies as quickly as paint and won't break the budget then Spraystone is the perfect coating.
SMOOTHROCK - PEARLS & METALS
Smoothrock is our original acrylic basecoat plaster that tints to any color giving the appearance of a smooth hand tooled plaster. Pearlescent or metallic gelled topcoats are then applied, producing a finish of unparalleled dimension and depth. This system is often used to create an effect that picks up multiple accent colors from fabric, wallpapers and furniture. Smoothrock basecoat can be trowel applied in any color and in a variety of techniques. Smoothrock can be invisibly repaired and cleans easily with household cleansers. This product does not need any additional sealers as the topcoats act like an acrylic Urethane fil.
VERSIPLAST/CRYSTAL COAT
Versiplast is one of our most popular products. It allows for any texture to be rendered without cracking or shrinking and needs no primer before distressing with glaze. This product has been used worldwide for years by faux artists to create unlimited effects. If your vision includes texture and relief then Versiplast should be your first product choice. Versiplast is frequently used for a skip trowel texture that is washed with colored glazes and over stenciled to create beautiful distressed walls.
VENETIAN PLASTER (SMOOTHROCK ACRYLIC)
This is our original Venetian Plaster from our Smoothrock line that renders the final appearance of a smooth hand-tooled plaster with mid to high sheen. This timeless finish is created by multiple overlapping with a stainless steel trowel, and then burnished to enhance both the light & dark tones of the same color for a marble-like appearance. This finish is a water-based acrylic, washable and available in hundreds of colors. Mixing this plaster in multiple colors with our Duragloss creates deep blended dimensional plaster effects.
GLITTEROCK SMOOTH (T.O. STONE NO FLAKE)
Glitterock Smooth is a pearl plaster with a rich silky feel that can be tinted with colorants or micas and blended into a cloudlike pearlescent finish. This product dries hard and smooth and fits into any décor. Glitterock Smooth is very different from any of our other coatings and is enhanced when accent lighting is present. This product is well suited for dining areas, bathrooms, and any area where a water resistant or soft understated finish is desired. Glitterock smooth can be installed in single or multiple colors and generally three surface passes are required to properly render this treatment. There is no polishing required and the plaster is fairly simple to use making this coating popular with professional and do it yourself applicators.
GLITTEROCK COARSE (3/4 ANGELSTONE + 1/4 TOPCOAT)
Glitterock Course is arguably the toughest premixed trowel applied system in the industry. For those looking to achieve a strong, durable hand finish, Glitterock Coarse is the way to go. This product can be tinted to any color or metallic and can be used inside and out with proper substrate preparation. Glitterock Course resists most stains and water making it suitable for commercial projects. Glitterock Coarse is an acrylic plaster containing large grain silica and bronze mica flakes. Our Metallic and pear topcoats can be mixed into Glitterock Coarse allowing for color continuity or any latex flat tinted paint can be added to Glitterock Coarse to create a pure non reflective color finish. The final effect feels like medium grit sandpaper. This finish is designed for production applications as it is rendered in only two passes with a large pool trowel. Stencil and raised relief patterns can be added to further customize the final effect. This product has the ability to render to a smoother final finish if the surface is water spritzed and knocked down at the proper time.
Top Coats and Primers
DURAGLOSS (STONE COAT)
Duragloss is arguably the best trowel applied acrylic clear topcoat in the industry. Any sheen level is possible from flat to mirror finish and one can be fooled into believing that this product is of a traditional wax finish. Duragloss offers excellent protection to Venetian plaster and can be over painted if needed. Duragloss has been specially designed to mix into our Acrylic Venetian plaster which allows the applicator to render multi colored semi transparent effects. Different ratios of Acrylic Venetian plaster to Duragloss will create various levels of opacity and translucency.
GLAZE
DuROCK Glaze is an acrylic glaze for interior applications. With this product, an infinite variety of designs and effects can be achieved. It is ideal for use over a variety of substrates including interior walls. The acrylic polymer used provides excellent resistance to water blushing or water whitening with excellent adhesion to several substrates. This polymer also exhibits excellent dirt pick-up resistance. There is the added benefit of film hardness, and good chemical and stain resistance.
FAUX GRIP (PREP COAT NCP)
Fauxgrip is an aggregate adhesive used for trowel applied priming of surfaces that are difficult to ahere to such as lami- nate, metal and ceramic. This product will not shrink or crack and creates the perfect bond between difficult substrates and decorative coatings. Fauxgrip can save time and labor on projects that would typically involve very detailed prep or removal of the existing substrate
GLITTEROCK PRIMER (BASE PRIMER 100)
Glitterock Primer is a high quality silica prime coat. It is used under Glitterock Coarse but can also be used under any texture for achieving a bond between the substrate and the more textured decorative coatings. This is a flexible acrylic paint with exterior capabilities. When tinted, this Roll on primer can be taped to expose a colored grout line effect seen in stonework. This coating is often used directly over extruded cement covered Styrofoam moldings on the exterior of homes and commercial properties. Glitterock Primer can be installed by roller, brush and spray equipment.
VERSILIME QUARTZ (AIRLESS)
Versilime Quartz is a primer for use with lime based systems but may be used anytime a high quality primer is required. This is a 100% acrylic primer with unbelievable adhesion strength. This primer can be tinted to almost any color making it great as a base under darker colors. Primer is generally considered the most important step in wall preparation and failure of paint or decorative coatings is frequently traced back to primer issues. Versilime quartz was designed to address prime coat issues making this coating a necessary addition to successful applications.